Slackware: kako naci mrezu?

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

INstalirao sam Slackware 14 u dual-boot sa Win7.Sada ne znam kako da nadjem mrezu.Kliknem na beli iksic u donjem desnom uglu i pise : "NetworkManager is not running. Please start it".
Ja idem na "Manange Connections" i mogu da otvorim samo Wired i VPN ali kod mene se radi o Wireless .Logovao sam se kao root.




Sta da radim?

• 2Ovo se svidja korisnicima: bocke, stefke001
  
  Registruj se da bi pohvalio/la poruku!

Za početak, nemoj koristiti sistem kao root, kreiraj (ako već nisi) običnan korisnički nalog i njega koristi u svakodnevnom radu (grafičko okruženje). Po potrebi, u terminalu se prebaci na root nalog (komandom su).

Drugi problem...daj nam izlaz komandi:
ifconfig
iwconfig
lspci
(sve komande izvršavaš kao root korinsik)

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

Evo:

lspci:
 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge
00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx)
00:0a.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 5)
00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode]
00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:12.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller
00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0 USB OHCI1 Controller
00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 3a)
00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 IDE Controller
00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA)
00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller
00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge
00:14.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RS780 [Radeon HD 3200]
01:05.1 Audio device: Advanced Micro Devices [AMD] nee ATI RS780 HDMI Audio [Radeon HD 3000-3300 Series]
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
03:0e.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)

iwconfig:
 lo        no wireless extensions.

wlan0     IEEE 802.11bgn  ESSID:off/any 
          Mode:Managed  Access Point: Not-Associated   Tx-Power=0 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:on
         
eth0      no wireless extensions.

 

ifconfig:

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 16436
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 0  (Local Loopback)
        RX packets 24  bytes 1360 (1.3 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 24  bytes 1360 (1.3 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0


• 1Ovo se svidja korisniku: stefke001
  
  Registruj se da bi pohvalio/la poruku!

Otvori terminal i kao root ukucaj sledeće:
iwlist wlan0 scanRezultat ove komande nam postavi u sledećoj poruci.

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

Posto mi se to desilo i sa debianom nasao sam temu pa sam uradio sledece:
 bash-4.2# iwlist wlan0 scan
wlan0     Interface doesn't support scanning : Network is down

bash-4.2# ifconfig wlan0 up
bash-4.2# iwlist wlan0 scan
wlan0     No scan results

bash-4.2#