Cudan zvuk, nesto kao sirena

Cudan zvuk, nesto kao sirena

offline
  • Pridružio: 17 Maj 2012
  • Poruke: 7

Pozdrav. Od pre neki dan imam problema sa racunarom Bebee Dol Iz kucista se neprestano cuje zvuk ( kao hitna pomoc ) nakon kojeg se racunar ugasi. Ne vjerujem da je cooler u pitanju, ventilator radi i ne vjerujem da se procesor pregrije mada nisam provjeravao temperaturu. Ne bih rekao ni da je do prasine, ocistio sam komplet, slotove od graf. rama... Pa me zanima sta vi mislite u cemu je kvar i na sta me upozorava moj napaceni komp. ? Laughing
Inace sam slab po pitanju racunara, pa molim malo razumijevanja tj. bez prozivki Mr. Green



Registruj se da bi učestvovao u diskusiji. Registrovanim korisnicima se NE prikazuju reklame unutar poruka.
offline
  • Pridružio: 02 Feb 2008
  • Poruke: 14018
  • Gde živiš: Nish

Mozes li prepoznati neki od ovih kodova ...



Piksi ::Evo onih BIOS beep codes :

1 short DRAM refresh failure
2 short Parity circuit failure
3 short Base 64K RAM failure
4 short System timer failure
5 short Process failure
6 short Keyboard controller Gate A20 error
7 short Virtual mode exception error
8 short Display memory Read/Write test failure
9 short ROM BIOS checksum failure
10 short CMOS shutdown Read/Write error
11 short Cache Memory error
1 long, 3 short Conventional/Extended memory failure
1 long, 8 short Display/Retrace test failed

1 long, 2 short Indicates a video error has occurred and the BIOS cannot initialize the video screen to display any additional information

Any other beep(s) RAM problem.

No Beeps No Power, Loose Card, or Short.
1 Short Beep Normal POST, computer is ok.
2 Short Beep POST error, review screen for error code.
Continuous Beep No Power, Loose Card, or Short.
Repeating Short Beep No Power, Loose Card, or Short.
One Long and one Short Beep Motherboard issue.
One Long and Two short Beeps Video (Mono/CGA Display Circuitry) issue.
One Long and Three Short Beeps. Video (EGA) Display Circuitry.
Three Long Beeps Keyboard / Keyboard card error.
One Beep, Blank or Incorrect Display Video Display Circuitry.

Error Tone. (two sets of different tones) Problem with logic board or SCSI bus.
Startup tone, drive spins, no video Problem with video controller.
Powers on, no tone. Logic board problem.
High Tone, four higher tones. Problem with SIMM.

1-1-1-3 Verify Real Mode.
1-1-2-1 Get CPU type.
1-1-2-3 Initialize system hardware.
1-1-3-1 Initialize chipset registers with initial POST values.
1-1-3-2 Set in POST flag.
1-1-3-3 Initialize CPU registers.
1-1-4-1 Initialize cache to initial POST values.
1-1-4-3 Initialize I/O.
1-2-1-1 Initialize Power Management.
1-2-1-2 Load alternate registers with initial POST values.
1-2-1-3 Jump to UserPatch0.
1-2-2-1 Initialize keyboard controller.
1-2-2-3 BIOS ROM checksum.
1-2-3-1 8254 timer initialization.
1-2-3-3 8237 DMA controller initialization.
1-2-4-1 Reset Programmable Interrupt Controller.
1-3-1-1 Test DRAM refresh.
1-3-1-3 Test 8742 Keyboard Controller.
1-3-2-1 Set ES segment to register to 4 GB.
1-3-3-1 28 Autosize DRAM.
1-3-3-3 Clear 512K base RAM.
1-3-4-1 Test 512 base address lines.
1-3-4-3 Test 512K base memory.
1-4-1-3 Test CPU bus-clock frequency.
1-4-2-4 Reinitialize the chipset.
1-4-3-1 Shadow system BIOS ROM.
1-4-3-2 Reinitialize the cache.
1-4-3-3 Autosize cache.
1-4-4-1 Configure advanced chipset registers.
1-4-4-2 Load alternate registers with CMOS values.
2-1-1-1 Set Initial CPU speed.
2-1-1-3 Initialize interrupt vectors.
2-1-2-1 Initialize BIOS interrupts.
2-1-2-3 Check ROM copyright notice.
2-1-2-4 Initialize manager for PCI Options ROMs.
2-1-3-1 Check video configuration against CMOS.
2-1-3-2 Initialize PCI bus and devices.
2-1-3-3 Initialize all video adapters in system.
2-1-4-1 Shadow video BIOS ROM.
2-1-4-3 Display copyright notice.
2-2-1-1 Display CPU type and speed.
2-2-1-3 Test keyboard.
2-2-2-1 Set key click if enabled.
2-2-2-3 56 Enable keyboard.
2-2-3-1 Test for unexpected interrupts.
2-2-3-3 Display prompt "Press F2 to enter SETUP".
2-2-4-1 Test RAM between 512 and 640k.
2-3-1-1 Test expanded memory.
2-3-1-3 Test extended memory address lines.
2-3-2-1 Jump to UserPatch1.
2-3-2-3 Configure advanced cache registers.
2-3-3-1 Enable external and CPU caches.
2-3-3-3 Display external cache size.
2-3-4-1 Display shadow message.
2-3-4-3 Display non-disposable segments.
2-4-1-1 Display error messages.
2-4-1-3 Check for configuration errors.
2-4-2-1 Test real-time clock.
2-4-2-3 Check for keyboard errors
2-4-4-1 Set up hardware interrupts vectors.
2-4-4-3 Test coprocessor if present.
3-1-1-1 Disable onboard I/O ports.
3-1-1-3 Detect and install external RS232 ports.
3-1-2-1 Detect and install external parallel ports.
3-1-2-3 Re-initialize onboard I/O ports.
3-1-3-1 Initialize BIOS Data Area.
3-1-3-3 Initialize Extended BIOS Data Area.
3-1-4-1 Initialize floppy controller.
3-2-1-1 Initialize hard-disk controller.
3-2-1-2 Initialize local-bus hard-disk controller.
3-2-1-3 Jump to UserPatch2.
3-2-2-1 Disable A20 address line.
3-2-2-3 Clear huge ES segment register.
3-2-3-1 Search for option ROMs.
3-2-3-3 Shadow option ROMs.
3-2-4-1 Set up Power Management.
3-2-4-3 Enable hardware interrupts.
3-3-1-1 Set time of day.
3-3-1-3 Check key lock.
3-3-3-1 Erase F2 prompt.
3-3-3-3 Scan for F2 key stroke.
3-3-4-1 Enter SETUP.
3-3-4-3 Clear in-POST flag.
3-4-1-1 Check for errors
3-4-1-3 POST done--prepare to boot operating system.
3-4-2-1 One beep.
3-4-2-3 Check password (optional).
3-4-3-1 Clear global descriptor table.
3-4-4-1 Clear parity checkers.
3-4-4-3 Clear screen (optional).
3-4-4-4 Check virus and backup reminders.
4-1-1-1 Try to boot with INT 19.
4-2-1-1 Interrupt handler error.
4-2-1-3 Unknown interrupt error.
4-2-2-1 Pending interrupt error.
4-2-2-3 Initialize option ROM error.
4-2-3-1 Shutdown error.
4-2-3-3 Extended Block Move.
4-2-4-1 Shutdown 10 error.
4-3-1-3 Initialize the chipset.
4-3-1-4 Initialize refresh counter.
4-3-2-1 Check for Forced Flash.
4-3-2-2 Check HW status of ROM.
4-3-2-3 BIOS ROM is OK.
4-3-2-4 Do a complete RAM test.
4-3-3-1 Do OEM initialization.
4-3-3-2 Initialize interrupt controller.
4-3-3-3 Read in bootstrap code.
4-3-3-4 Initialize all vectors.
4-3-4-1 Boot the Flash program.
4-3-4-2 Initialize the boot device.
4-3-4-3 Boot code was read OK.



offline
  • Pridružio: 05 Jun 2012
  • Poruke: 126

Zavisi od maticne (tip BIOS) ami,award,phoenix,mr,quadtel,compaq,ast,hewlett packard(hp) sve daju razlicite signale.......
Dakle Naziv maticne ploce i koliko bipova cujes kratko i jasno.....

offline
  • Rade Jekić
  • Pridružio: 05 Okt 2005
  • Poruke: 3005
  • Gde živiš: Valjevo

Ovakav zvuk koji dopire iz bipera upozorava na CPU problem. U ogromnom broju slučajeva u pitanju je pregrevanje (najčešće prouzrokovano loše montiranim hladnjakom). Skini hladnjak i ventilator sa procesora, skini staru pastu sa procesora i hladnjaka, skini procesor, očisti prašinu ako je ima, vrati procesor, nanesi novi sloj termalne paste i vrati hladnjak i ventilator na svoje mesto. Kada si se uverio da je hladnjak dobro nalegao na procesor i da nema pomeranja ("disanja") poveži kabl od ventilatora na matičnu ploču, priključi napojni kabl u napajanje računara i upali ga. Ima li promene?

offline
  • Pridružio: 17 Maj 2012
  • Poruke: 7

Gorane: Slabo mi ti kodovi sta znace Very Happy
Evo Cesar:
Maticna: Asus P4B33
Procesor: Intel 1.82 GHz, 512 ram Embarassed
Bios: Award Software.Inc
Zvuk je slican sireni hitne pomoci, onako sa dva tona, konstantno, zna se cuti cijelo vrijeme dok radim za racunarom sve dok se ne ugasi, a zna se desiti da prestane,ali opet povremeno izbaci onako kratak zvuk sa jednim tonom xD

Drumer:

Instalirao sam sa cd-a asusov program za mjerenje temperature , i evo sta je ustanovio:

Cpu Temperature: 32C/87 F
MB Temperature: 30C/84F
Dakle po ovome temperatura otpada i vjerovatno nije u pitanju pregrijavanje Iili mozda jeste, samo sto nisam dovoljno opteretio procesor Bebee Dol Brzina Cpu ventilatora je 1200 rmp, ako bih u setingsu povecao brzinu na 2000-3000 rmp-a da li bi to poboljsalo hladjenje?

Skidao sam Hladnjak, ocistio prasinu, vratio na mjesto i pricvrsio(mislim da je dobro legao, ne pomijera se i cvrst je). E sad, ne znam da li je u pasta ostecena, gledao sam i ne izgleda ostecena(izgrebana) sem sto se sa sve cetiri strane odlicno vidi urezani trag na procesoru ( sto je normalno)? Da li da skidam ovu pastu i nanosim novu? Mad Nakon koliko vremena se ona mijenja, da li je to nakon svakog skidanja hladnjaka ili dok se ne osteti?

offline
  • akuci  Male
  • Legendarni građanin
  • Aleksandar
  • Pridružio: 11 Maj 2008
  • Poruke: 2758
  • Gde živiš: Novi Sad

Sasvim moguce je da se ustvari ventilator ugasi zbog niske temperature procesora i ploča se oglašava. Obicno je to opcija "CPU Fan Fail Warning"

offline
  • Pridružio: 17 Maj 2012
  • Poruke: 7

Pa sta mi je da radim? Very Happy
Izludi me! Da nosim u servis? Nisam bas pri novcu pa koliko bi kostalo od prilike da mi otklone ovaj kvar? Znaci, kad se ugasi sad mi je poceo pustati upozorenje na zvucnik. Mislim d ovo kaze: System failed ( CPU ? :// ) card

Ko je trenutno na forumu
 

Ukupno su 885 korisnika na forumu :: 49 registrovanih, 7 sakrivenih i 829 gosta   ::   [ Administrator ] [ Supermoderator ] [ Moderator ] :: Detaljnije

Najviše korisnika na forumu ikad bilo je 3466 - dana 01 Jun 2021 17:07

Korisnici koji su trenutno na forumu:
Korisnici trenutno na forumu: AC-DC, Alibaba1981, Atomski čoban, b_z_b, beowl, black venom, blackjack, Bobrock1, botta, chica, darionis, darkangel, djboj, djox00, doklevise, ds69, dule10savic, FOX, Frunze, galerija, goxin, haris1913, HrcAk47, hyla, ink, kayvan6079, ljuba, MB120mm, mercedesamg, Metanoja, Milan A. Nikolic, miodrag, nikoladim, pceklic, Pyrqe, ruso, sasa87, Skywhaler, slonic_tonic, stagezin, stokssone, Toper, vathra, VJ, Vlad000, Vlada1389, ZetaMan, zillbg, Zoca