Dodavanje RAM memorije BSOD

Dodavanje RAM memorije BSOD

offline
  • Pridružio: 24 Nov 2020
  • Poruke: 3

Pozdrav svima. Imam problem sa dodavanjem nove memorije. Imao sam 2 x 4GB kingston hyperx fury black DDR4 2133mhz , dodao sam jos 2 x 4GB kingston hyperx fury black DDR4 2400mhz. Medjutim dobijam BSOD. Kada izvadim staru memoriju i ostavim novu samu radi bez problema, ali ne mogu nikako da ih uparim. Probao sam razne kombinacije po slotovima. Trenutno je stanje kao na slici ali ni to ne daje rezultate. Maticna ploca asus Z170m plus





Crash dump directories:
C:\WINDOWS
C:\WINDOWS\Minidump

On Tue 24-Nov-20 10:46:08 your computer crashed or a problem was reported
crash dump file: C:\WINDOWS\Minidump\112420-28234-01.dmp
This was probably caused by the following module: win32kbase.sys (0xFFFFEDD57D5BF9F0)
Bugcheck code: 0x50 (0xFFFFEDA660F38E58, 0x2, 0xFFFFEDD57D5BF9F0, 0x2)
Error: PAGE_FAULT_IN_NONPAGED_AREA
file path: C:\WINDOWS\system32\win32kbase.sys
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: Base Win32k Kernel Driver
Bug check description: This indicates that invalid system memory has been referenced.
This appears to be a typical software driver bug and is not likely to be caused by a hardware problem.
The crash took place in a Microsoft module. Your system configuration may be incorrect. Possibly this problem is caused by another driver on your system that cannot be identified at this time.

On Tue 24-Nov-20 10:33:48 your computer crashed or a problem was reported
crash dump file: C:\WINDOWS\Minidump\112420-32984-01.dmp
This was probably caused by the following module: ntoskrnl.exe (nt+0x1C3B20)
Bugcheck code: 0x50 (0xFFFFF70A49BCD768, 0x0, 0xFFFFF8056B809F6D, 0x2)
Error: PAGE_FAULT_IN_NONPAGED_AREA
file path: C:\WINDOWS\system32\ntoskrnl.exe
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: NT Kernel & System
Bug check description: This indicates that invalid system memory has been referenced.
This appears to be a typical software driver bug and is not likely to be caused by a hardware problem.
The crash took place in the Windows kernel. Possibly this problem is caused by another driver that cannot be identified at this time.

On Tue 24-Nov-20 10:01:10 your computer crashed or a problem was reported
crash dump file: C:\WINDOWS\Minidump\112420-33640-01.dmp
This was probably caused by the following module: ntoskrnl.exe (nt+0x1C3B20)
Bugcheck code: 0xA (0x11, 0x2, 0x0, 0xFFFFF8041C62B08F)
Error: IRQL_NOT_LESS_OR_EQUAL
file path: C:\WINDOWS\system32\ntoskrnl.exe
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: NT Kernel & System
Bug check description: This indicates that Microsoft Windows or a kernel-mode driver accessed paged memory at DISPATCH_LEVEL or above. This is a software bug.
This bug check belongs to the crash dump test that you have performed with WhoCrashed or other software. It means that a crash dump file was properly written out.
The crash took place in the Windows kernel. Possibly this problem is caused by another driver that cannot be identified at this time.



Registruj se da bi učestvovao u diskusiji. Registrovanim korisnicima se NE prikazuju reklame unutar poruka.
offline
  • Pridružio: 02 Sep 2003
  • Poruke: 4954

Proveri da BIOS nije automatski podesio brzinu memorije na 2400Mhz, mada bi trebalo da se prilagodjava sporijoj.



offline
  • Pridružio: 24 Nov 2020
  • Poruke: 3

Podesavanje je na "auto", prikazuje manju brzinu

offline
  • Pridružio: 02 Sep 2003
  • Poruke: 4954

Probaj na rucno, menjaj latencije i malo povecaj napon. Pokusaj da nadjes podesavanje na netu za tvoju plocu i tu memoriju. Da li imas poslednji bios na ploci?

offline
  • Pridružio: 24 Nov 2020
  • Poruke: 3

Napisano: 24 Nov 2020 15:57

U biosu je sve na auto i podeseno na iste vrednosti sve.
Ubo sam trenutno neki redosled (2400-2133-2400-2133), za sada radi Ok. Da vidim da li ce to da potraje Smile

Dopuna: 24 Nov 2020 17:48

Nema ovde izgleda resenja, cim ubacim cetvrti stap pocne da pravi problem. Sasvim normalno radi sa 2 x 2400 , 1 x 2133. Elem, BIOS nije zadnji ali iskreno da ti kazem ne zeza mi se sada oko biosa. Jos mi samo i tu treba da krene nesto po zlu Smile . Probacu jos malo nesto da cacnem, ako nista neka ih ova 3 stapa i to je to.

Ko je trenutno na forumu
 

Ukupno su 763 korisnika na forumu :: 24 registrovanih, 2 sakrivenih i 737 gosta   ::   [ Administrator ] [ Supermoderator ] [ Moderator ] :: Detaljnije

Najviše korisnika na forumu ikad bilo je 3466 - dana 01 Jun 2021 17:07

Korisnici koji su trenutno na forumu:
Korisnici trenutno na forumu: Apok, Bane san, Ben Roj, delrey, draganca, gasha, goxin, Leonov, MB120mm, MiroslavD, nenad81, nuke92, Posmatrac77OKB, Rogonos, ser.hill, Srky Boy, Stamena, Stanlio, stegonosa, tmanda323, udbas, vladetije, x9, |_MeD_|